Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Fence Installation: The Los Angeles Owner’s Guide
ES Windows fence installation in Los Angeles typically runs $4,130 to $10,620 installed, and we stock the common track, hinge, and latch components on our trucks so most jobs finish in a single visit. You have ES Windows fencing around your property, and one section is now sagging, dragging, or the gate won’t latch the way it used to. That failure usually starts small: a worn roller, a hinge that’s pulled loose from the post, or a track that’s warped after a few Los Angeles summers.
We’re Penhallow Remodeling, and while we’re not affiliated with ES Windows, we work with their fence systems regularly across Los Angeles. Trevor Nash has seen enough ES Windows fence sections in this city to know exactly which parts fail first and what it takes to get them square and rolling again. This page gives you the straight answer on cost, compatibility, and whether the repair is something you should attempt yourself.
Which ES Windows Models This Applies To
ES Windows fence systems sold in greater Los Angeles fall into a few recognizable families, and the compatibility question comes down to track profile and roller diameter. The older ES Windows sliding fence panels used a top-hung track system with nylon rollers that ride inside an extruded aluminum channel. Newer systems shifted to a bottom-roller design with adjustable carriage assemblies. If you can read the stamp on the inside edge of the track or the side of the post, it will usually give you the series and the panel width. If the stamp is worn off, we measure the roller body and the channel opening, because mixing a 1-1/4 inch roller into a track cut for 1-1/2 inch hardware will bind within a month.
When it comes to OEM versus quality aftermarket, the honest answer is that OEM ES Windows rollers are hard to source on short notice in Los Angeles, and a good aftermarket replacement often outlasts the original. The original rollers were never the high point of these fence systems. What matters more than the name on the box is the bearing inside: a sealed stainless bearing stands up to sprinkler overspray and salt air from the coast far better than the open brass bearings ES Windows used on early runs. For track, we insist on OEM or a machine-shop match, because tolerance there isn’t something you fudge.
Styles & brands we work with
Signs Your ES Windows Fence Installation Is Failing
- The gate grabs or jumps as you open it. This is almost always a flat-spotted roller or a worn bearing. Once the roller stops spinning freely, it starts scraping the track and wearing a groove into the aluminum.
- The panel leans when closed but straightens when open. The hinge post has moved or the hinge flange is pulling away from the post body. In Los Angeles, the culprit is often wood fence posts that have dried and shrunk in the heat, loosening every screw they hold.
- You have to lift the panel to get it to latch. The bottom roller carriage has lost its adjustment, or the bracket has slipped. This is a ten-minute fix if you catch it early; ignored, it damages the latch and the panel corner.
- The track is noisier than it used to be. Grit from the Santa Ana winds gets into the channel and acts like sandpaper on the roller faces. Noise isn’t failure yet, but it’s the warning sign that tells you to clean and lubricate before you’re buying parts.
- The gate latch won’t hold after a windy day. The latch plate and strike have shifted out of alignment. On ES Windows panels, the latch is mounted to the panel extrusion, and repeated slamming bends the mounting tab until the catch no longer seats.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Los Angeles, a full ES Windows fence installation or a section rebuild lands between $4,130 and $10,620. The spread comes down to how many panels you have, whether the posts are still solid, and whether we can reuse the existing track. A simple two-panel gate repair with new rollers, hinges, and latch typically runs at the low end of that range. Rebuilding a long run with new track, multiple posts, and realignment across the whole fence line pushes toward the top.
Your written number includes parts, labor, haul-off of any failed hardware, and cleanup. You get the price before we start, under the Kingswell standard, and the number on day one is the number on the invoice. The work is covered by our 365-Day Done Right Promise: if the fence binds, drags, or fails within that year, we come back and fix it at no charge. No service call fee, no re-inspection fee. You also get our written guarantee on the repair itself.
DIY or Call Us?
ES Windows fence systems don’t have high-tension springs, so this isn’t in the same danger category as a garage door. What they do have is weight. A full aluminum fence panel is heavier than most homeowners expect, and when it comes off its track, it wants to fall. If your panel has come off the track and you’re holding it up with a 2×4, that’s the moment to call us at (213) 277-6578.
What you can safely check: wipe down the track, look for obvious debris, and see whether the roller faces are flat or the bearings have play. If you’re just diagnosing, that’s fine. If you’re loosening bracket bolts or trying to pop a panel back onto its track alone, the risk of a pinched finger or a bent panel isn’t worth the savings. Give you a number first, then pick up the tools. We’ll come out, tell you exactly what it needs, and hand you a written price before anyone touches a wrench.
FAQs
Plan on eight to twelve years for the original rollers, with the bearings typically failing before the nylon wheel. In Los Angeles the two things that shorten that lifespan are sprinkler overspray and wind-driven grit, both of which attack the bearing. Give us a call at (213) 277-6578 and we’ll take a look at what you’ve got.
Rollers and latches get replaced, not rebuilt, because the bearing and spring internals aren’t serviceable. Tracks can often be repaired in place if the damage is limited to one section, and we’ll always choose the repair over a full replacement when your budget and the fence’s condition support it. Call us for an honest assessment.
Most single-panel repairs, including roller, hinge, and latch replacement, finish in two to three hours once we’re on site. Full fence section rebuilds take a day, and a complete replacement run can take two. We’ll give you the timeline with the written estimate.
We stock common ES Windows-compatible rollers, adjustable carriages, hinges, and latch assemblies in our Los Angeles service vehicles, along with a few track profiles. For oddball panel widths or discontinued series, we source from local Los Angeles metal suppliers, usually within a couple of business days.
If your ES Windows fence is sagging, dragging, or just won’t latch like it used to, call (213) 277-6578 and we’ll set up a time to look at it. The estimate is free, and the price you get in writing is the price you’ll pay.
Written by Trevor Nash, Owner, Penhallow Remodeling Los Angeles at Penhallow Remodeling Los Angeles, serving Los Angeles and nearby areas.
