Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Los Angeles Owner’s Guide
CGI kitchen remodeling in Los Angeles typically runs $16,520 – $53,100 installed, depending on cabinet line, countertop material, and whether you’re replacing a single failed component or rebuilding the whole room. In most cases we can match your existing CGI cabinet doors, drawer fronts, and hardware within 7 to 10 business days, then install them properly so they don’t sag, bind, or chip the way the originals did. Homeowners usually find us because a hinge tore out of a particleboard stile, a drawer slide bent mid-pull, or the thermofoil on a door has started peeling at the edges.
What most people don’t know is that “CGI” in the kitchen cabinet trade usually refers to CGI Windows & Doors (a Miami-based manufacturer known for impact-rated aluminum products) or to CGI cabinetry lines sourced through regional suppliers that serve Los Angeles remodelers. If you’re sitting on a CGI-branded kitchen product and a door or drawer has failed, we treat it like any other kitchen repair: identify the exact component, match it or replace the run, and put it in writing before we touch a screwdriver. Penhallow Remodeling Los Angeles is an independent contractor and not affiliated with CGI or its distributors.
Which CGI Models This Applies To
The honest answer is that CGI-branded kitchen cabinets in Los Angeles come from a few different supply chains, and the labeling isn’t always consistent. Some homeowners have CGI aluminum-framed cabinet doors, which are more common in coastal Los Angeles homes where salt air chews through wood and particleboard faster. Others have CGI-imported melamine or thermofoil cabinet boxes that came through a kitchen-and-bath showroom in the San Fernando Valley or Orange County during a remodel 10 to 15 years ago. The compatibility question comes down to hardware bore spacing, hinge cup diameter, drawer slide length, and door overlay measurements, not just the name printed on the box.
Here’s the gotcha we see on a lot of older CGI installs in Los Angeles: the bore spacing on European-style cup hinges is either 35mm or 45mm, and the two are not interchangeable. If your cabinet door has 45mm holes and the replacement hardware you found online is 35mm, the door will hang crooked no matter how many times you adjust it. We also see drawer slides with 12-inch, 18-inch, or 21-inch travel on the same-looking CGI cabinet run, because the original installer mixed what they had in the truck. We measure every hinge, slide, and door before we quote, so the replacement actually fits the cabinet, not approximate it.
On the OEM-versus-aftermarket question: for CGI aluminum-framed doors, OEM replacement parts through the original distributor are usually the cleanest path, but lead times out of the Miami-area warehouses can stretch four to six weeks. Quality aftermarket equivalents from brands like Blum, Salice, and Hettich are often in our Los Angeles supplier’s inventory same-week, and in most cases they outperform the original hardware. We stock Blum soft-close replacement hinges, 18-inch and 21-inch full-extension slides, and standard overlay catch hardware on the truck, so a door or drawer that’s hanging loose can usually be put back to work the same day we look at it.
Styles & brands we work with
Signs Your CGI Kitchen Remodeling Is Failing
- Thermofoil peeling at the bottom edge of a door. This is the most common CGI cabinet failure we see in Los Angeles, and it’s heat and humidity related. The vinyl layer separates from the MDF core, usually starting at the seam, and once it lifts, water gets in and swells the board. Replacement is the fix, not regluing.
- A hinge has torn out of the door stile and the door now droops. CGI doors made from particleboard or MDF will eventually wallow out the hinge cup holes, especially on the heavily used sink base and the cabinet under the microwave. The screw holes strip, the door sags, and the corner starts gouging the adjacent cabinet face.
- A drawer slide sticks, grinds, or dumps the drawer when you pull it. Ball-bearing slides fail when a bearing cage breaks or the slide rail bends from an overloaded drawer. On CGI cabinet boxes, we also see installer error where the slide was mounted a quarter-inch low, which forces the drawer to ride against the cabinet opening.
- The corner joint on a cabinet face frame is separating. In drier parts of Los Angeles like the Valley, wood cabinet face frames can shrink enough over a few years that the corner joinery opens up and the joint line becomes visible through the finish. It’s cosmetic at first, but the gap widens and the cabinet can start racking.
- Soft-close mechanisms stopped catching. If your doors and drawers used to ease shut and now clap against the cabinet frame, the damper inside the soft-close hinge or slide has lost pressure. It’s a $12 to $18 part per hinge, but it requires pulling the door and resetting the clip mechanism.
Replacement Cost & What’s Included
For Los Angeles homeowners dealing with a failed CGI cabinet door, drawer front, or hardware failure, the installed range we quote most often is $945 – $2,950 for the backsplash-level repair scope (replacing a single run of hardware, rehanging doors, or swapping a damaged drawer front and slide). If the damage is widespread and you’re replacing multiple doors, drawer boxes, and hardware across the kitchen, the number moves into the $4,720 – $15,340 cabinet installation range. Full kitchen remodels where we’re pulling the existing CGI cabinets entirely and rebuilding run $16,520 – $53,100 in Los Angeles, driven by cabinet line (KraftMaid and Wellborn are our two most-specified lines), countertop material (Cambria, Silestone, or Caesarstone quartz carry different price points), and whether the layout changes.
Every number we give is a written price before work starts, not a verbal range we can drift from later. That price includes the replacement parts, the labor, cleanup, and our written guarantee: if the repair fails inside a year, we come back and fix it at no charge. That’s the 365-Day Done Right Promise, and it’s in writing on every job we do in Los Angeles.
Key Takeaways
- CGI kitchen component failures in Los Angeles are most often thermofoil peeling, stripped hinge cups, or failed drawer slides.
- Installed repair costs typically run $945 – $2,950; broader replacement work runs $4,720 – $15,340; full remodels run $16,520 – $53,100.
- We measure hinge bore spacing and slide length before quoting, so the replacement fits the first time.
- Every Los Angeles job gets a written price before work starts and a 365-day written guarantee. If it fails inside the year, we come back and make it right at no charge.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
What you can safely check yourself: pull the drawer out and count the slide length, look at the hinge cup for a 35mm or 45mm marking, and snap a photo of the label inside the cabinet box if one is still there. That saves us a trip and gets you a closer estimate on the first call. What we’d rather you not attempt: rebuilding a stripped hinge cup with wood filler and longer screws, or trying to re-stick peeling thermofoil with contact cement. Those two repairs fail again fast, and on aluminum-framed CGI doors, drilling new holes without a template leaves you with a door that hangs worse than before. Give us a call at (213) 277-6578 and we’ll match the part, quote it in writing, and get it on the truck.
FAQs
In Los Angeles, CGI thermofoil and melamine cabinet boxes typically last 12 to 20 years before door edges peel, hinge cups strip out, or the box begins to show water damage at the sink base. Aluminum-framed CGI doors can outlast the cabinets they’re hung on; we regularly see 25-year-old frames that just need new hinges and damper hardware. Call (213) 277-6578 and we’ll tell you honestly whether your cabinets are worth repairing or have hit the point where we’d recommend replacement.
A peeling CGI thermofoil door generally cannot be repaired in a way that lasts, because once the vinyl lifts from the MDF core, moisture has usually already started swelling the board inside. Touch-up kits and regluing fail within a few months, especially in humid Los Angeles coastal areas. We can match the door or the full run and quote the replacement in writing, before any work begins. Call (213) 277-6578 for a free estimate.
Most CGI hardware replacement jobs (hinges, drawer slides, dampers) are done in a single visit of 2 to 4 hours, and we stock common Blum and Salice replacement parts on the truck. Matching a door or drawer front from a Los Angeles supplier usually adds 7 to 10 business days after we confirm the measurement and finish. Call (213) 277-6578 and we’ll give you a real arrival window and a real completion date before you commit to anything.
We stock aftermarket replacement hinges and drawer slides that match the 35mm and 45mm bore patterns and common slide lengths used on CGI cabinets in Los Angeles, and we source doors, drawer fronts, and aluminum frame components through our local supplier network as needed. You don’t need to order parts yourself. Call (213) 277-6578 and we’ll identify the exact component, price it in writing, and schedule the swap.
Ready to Get Your CGI Kitchen Working Again?
Whether it’s one drawer that won’t stay closed or a full row of doors peeling at the corners, the next step is the same: call Penhallow Remodeling Los Angeles at (213) 277-6578. We’ll give you a written price before any work starts, show up in the window we promised, and stand behind the repair with our 365-Day Done Right Promise. Trevor Nash and our crews have been measuring, matching, and fixing cabinetry across the Los Angeles Basin for the better part of two decades. Give you a number first, then pick up the tools.
Written by Trevor Nash, Owner, Penhallow Remodeling Los Angeles at Penhallow Remodeling Los Angeles, serving Los Angeles and nearby areas.
